Testing (Cont’d)

Power Factor (PF)

 

Power factor (PF) is one of those mysterious properties of AC that even most electrical engineers have a hard time explaining.  A thorough technical discussion goes beyond the scope of this review (not to mention this author’s understanding).  For a more detailed discussion about PF, please look here.

 

Akasa Power+ 650W Power Supply Review - Cases and Cooling 27

 

Power factor is defined as the ratio of true power (measured in watts) to apparent power (measured in Volt Amps).  It measures how effectively AC power is being used by a device.  The difference between true power and apparent power is expressed as the power factor and results from the way true power and apparent power are measured.  Ideally we would like to have true power and apparent power equal to one another, which would result in a PF of 1.00 or 100% effective power utilization. 

 

I measured the AC Power Factor with a WattsUp? Pro power analyzer.  The Akasa 650W power supply incorporates active power factor correction circuits, which resulted in all PF readings being at or close to 1.0. 

 

Akasa Power+ 650W Power Supply Review - Cases and Cooling 28

 

Note: A power supply with active PFC is more environmentally friendly (doesn’t pollute the AC transmission grid) and will use less current, but it will not save you money on your monthly electric bill unless you are a commercial user whose bill is based on PF and usage.   

 

Efficiency

 

The overall efficiency of a power supply is very important, especially when operating in a silent, fan-less mode.  The less waste heat generated the better!  Efficiency is defined by the power output divided by the power input and is usually expressed as a percentage.  If a PSU were a 100% efficient (which none are) 400 watts of AC power going in would result in 400 watts of DC power coming out (with no waste heat to dissipate).  In the real world there are always inefficiencies and power is lost in the form of heat during the conversion process.

 

Akasa Power+ 650W Power Supply Review - Cases and Cooling 29

 

The latest revisions to the ATX12V Power Supply Design Guide V 2.2 have continued to increase the efficiency recommendations for PC switching mode power supplies.  And the latest revision (Ver 2.2) now lists both required and recommended minimum efficiencies.

 

Akasa Power+ 650W Power Supply Review - Cases and Cooling 30

 

I measured the AC power input to the Akasa 650W PSU with the WattsUp? Pro watt meter and calculated the combined DC power output by summing the products of all the DC outputs (volts x amps) for five different DC loads.

 

Akasa Power+ 650W Power Supply Review - Cases and Cooling 31

 

The overall efficiency of the Akasa Power+ doesn’t quite live up to the new design recommendations of 80% efficiency for a typical load.  However, this is when the PSU is operating on 115 VAC.  When operating on 230 VAC, the efficiency will probably be a few % points higher.  And to be fair, Akasa has newer power supplies in their high efficiency and ultra quiet series, which comply with the ATX12V 2.2 guidelines, so their efficiency should be better.

 

Akasa Power+ 650W Power Supply Review - Cases and Cooling 32

 

The 80 Plus Computer Power Supply Program

 

 

There is a growing awareness among users, PC manufacturers and electric utilities regarding the money and natural resources that could be saved by adopting higher efficiency power supplies.  One group that is spearheading this new movement is Ecos Consulting.  You can learn more about their efforts to promote power supplies with better than 80% efficiency by visiting the 80 Plus Program website.

 

Spending a little more money up front to purchase a high efficiency power supply may very well pay for itself over the lifetime of the PC… 🙂

 

Differential Temperature and Noise Levels

 

The differential temperature across the Akasa 650W power supply was calculated by subtracting the ambient room air temperature (T in) from the temperature of the warm exhaust air flowing out of the power supply (T out) when the fan was running. 

 

Thermocouples were placed at the air inlet and exhaust outlet. The ambient room air temperature was 24ºC (75ºF) +/- 1ºC during testing.

 

T in = temperature of air entering power supply

T out = temperature of air exhausting from power supply

ΔT = T out – T in

 

Sound pressure level readings were taken 3′ in front of the PSU in an otherwise quiet room.  The power supply was placed on a foam rubber mouse pad during testing.  The ambient noise level was ~30 dBA. 

 

Akasa Power+ 650W Power Supply Review - Cases and Cooling 33

 

The two 80mm Sanyo Denki fans do a very good job of keeping all the internal bits cool but at the expense of being very noisy.  The Power+ is a performance PSU, not a quiet PSU.

 

« PreviousNext »