Power Factor (PF)
Power factor (PF) is one of those mysterious properties of AC that even most electrical engineers have a hard time explaining. A thorough technical discussion goes beyond the scope of this review (not to mention this author’s understanding). For a more detailed discussion about PF, please look here.
Power factor is defined as the ratio of true power (measured in watts) to apparent power (measured in Volt Amps). It measures how effectively AC power is being used by a device. The difference between true power and apparent power is expressed as the power factor and results from the way true power and apparent power are measured. Ideally we would like to have true power and apparent power equal to one another, which would result in a PF of 1.00 or 100% effective power utilization.
I measured the AC Power Factor with an Extech power analyzer. The GameXstream power supply incorporates active power factor correction circuits, which resulted in all PF readings being very close to 1.0.
Note: A power supply with active PFC is more environmentally friendly (doesn’t pollute the AC transmission grid) and will draw less current, but it will not save you money on your monthly electric bill unless you are a commercial user whose bill is based on PF and usage.
The overall efficiency of a power supply is very important, especially when operating at higher power levels. The less waste heat generated the better! Efficiency is defined by the power output divided by the power input and is usually expressed as a percentage. If a PSU were a 100% efficient (which none are) 400 watts of AC power going in would result in 400 watts of DC power coming out (with no waste heat to dissipate). In the real world there are always inefficiencies and power is lost in the form of heat during the conversion process.
The latest revisions to the ATX12V Power Supply Design Guide V 2.2 have continued to increase the efficiency recommendations for PC switching mode power supplies. And the latest revision (Ver 2.2) now lists both required and recommended minimum efficiencies.
I measured the AC power input to the GameXstream PSU with the Extech power analyzer and calculated the combined DC power output by summing the products of all the DC outputs (volts x amps) for five different DC loads.
The overall efficiency of the OCZ GameXstream 700W power supply is very good and meets the latest recommendations with ease. The efficiency would most likely be even higher when operating on 230 VAC instead of 115 VAC, which would put it very close to OCZ’s claim of up to 85% efficiency (however not at maximum load).
The 80 Plus Computer Power Supply Program
The 80 Plus Computer Power Supply Program
There is a growing awareness among users, PC manufacturers and electric utilities regarding the money and natural resources that could be saved by adopting higher efficiency power supplies. One group that is spearheading this new movement is Ecos Consulting. You can learn more about their efforts to promote power supplies with better than 80% efficiency by visiting the 80 Plus Program website.
Spending a little more money up front to purchase a high efficiency power supply may very well pay for itself over the lifetime of the PC, especially when you are using this much powerâ€¦ 🙂
Differential Temperature and Noise Levels
The differential temperature across the GameXstream 700W power supply was calculated by subtracting the ambient room air temperature (T in) from the temperature of the warm exhaust air flowing out of the power supply (T out).
Thermocouples were placed at the air inlet and exhaust outlet. The ambient room air temperature was 24ÂºC (75ÂºF) +/- 1ÂºC during testing.
T in = temperature of air entering power supply
T out = temperature of air exhausting from power supply
Î”T = T out – T in
Sound pressure level readings were taken 3′ in front of the PSU in an otherwise quiet room. The power supply was placed on a foam rubber mouse pad during testing. The ambient noise level was ~30 dBA.
Below 300W output, the PSU was very quiet. Above 300W, the cooling fan ramped up to where it was noticeable and at 700W it was starting to get loud. Unfortunately, I was not able to measure the SPL when the power supply was running under full load (692W) because all the cooling fans on the programmable DC loads had kicked in at this point. The GameXstream 700W PSU is a little noisier than the Zalman ZM600-HP at higher power levels due to the different fans used and the fact that the GameXstream is rated for an additional 100 watts of output. That extra capacity requires a little more cooling, which results in a little more noise.