Assembling Your Own High Power AVR
OK, you can put away your soldering irons and ESD straps. We’re not actually going to build an AVR from the ground up. What we are going to do is assemble a relatively high-end AVR that incorporates the majority of the latest-and-greatest features along with power to spare for a fraction of what you might otherwise expect to pay for separates.The AVR is the central hub of your home theater system. It combines the functionality of numerous devices (AV switcher, tuner, audio decoders, video processor, pre-amps, power amps, etc.) into a single box. While the modern AVR performs most tasks admirably some compromises have to be made. One area where many AVRs struggle is delivering enough power to safely drive all the connected speakers. The two main factors that limit an AVR’s power output are the internal power supply’s total power output capacity and the amplifier’s ability to dissipate heat. If your AVR’s combined power output isn’t adequate to drive all your speakers to the level you want then the sound may seem strained or clipping may result, which will grossly distort the sound and can damage your speakers. Connecting multiple 6 ohm or 4 ohm speakers to an AVR can easily overload the internal amplifiers causing the AVR to overheat, shutdown, and shorten its life. So let’s look at some options:
• Purchase a mid-level or high end AVR with a strong power amp section
• Go with separates: AV processor and one or more power amps
• Combine a solid AVR with an outboard, multi-channel power amp
I was faced with this dilemma a year ago when I put together my latest home theater. I planned to use a 7.2 channel system in a large room. My speakers were all 4 ohm and I wanted to be able to play back movie sound tracks at near reference level. This presented a huge challenge to most AVRs. After considering the three options above I chose to go with a solid mid-level AVR and add a 5-channel outboard power amp to do the heavy lifting. My timing put me at the start of a new model year so I picked up a nice Denon AVR-3808CI on close-out for half price and purchased an Emotiva XP-A5 power amp with the money I saved. This combination gave me all the features I was looking for at a significant cost savings versus going with a high end AVR (rated to handle seven 4 ohm speakers) or a stack of separates.
Here are several examples of some different configurations you might use when combing an AVR with one or more power amps.
Combining a good AVR of your choice with an outboard power amp can deliver a lot of bang for the buck. One watch-out if you decide to go this route is to make sure the AVR you select has analog pre-amp outputs; very few entry level units do. Here are a few of the lower cost AVRs on the market today that offer pre-outs.
Lower Cost AVRs with Pre-Amp Outs:
• Marantz SR5004 ($849)
• Onkyo TX-SR707 ($899)
• Denon AVR-3310ci ($1,499)
• Pioneer Elite VSX-21TXH ($800)
• Yamaha RX-V665 ($549)
Outboard power amplifiers come in many different configurations and are available from several different manufacturers. Emotiva happens to be one of my personal favorites as I have had very good experiences with their products.
Emotiva Power Amplifiers:
• XPA-1 ($999) 500W rms x 1 (8 ohms)
• XPA-2 ($799) 300W rms x 2 (8 ohms)
• XPA-3 ($599) 200W rms x 3 (8 ohms)
• XPA-5 ($799) 200W rms x 5 (8 ohms)
• UPA-7 ($699) 125W rms x 7 (8 ohms)
• UMC-1 ($699) 7.1 Pre/Pro (used instead of an AVR)
Note: When it comes to amplifiers driving speakers, it’s better to have too much power than not enough. Not having enough power to adequately drive your speakers to the listening levels you want can permanently damage your speakers because when the amplifiers are pushed too hard the output signals can be clipped (sign wave converted towards a square wave). Having extra power gives your system headroom and insures that even during peak demands the amplifiers will be able to output the desired signal without distortion or clipping. The only real down side to having too much power is potentially paying for something you will never use. It’s similar to buying a PC power supply – it’s better to err on the high side rather than suffer the consequences of not having enough power to meet peak demands either now or in the future.




This was a great series that
This was a great series that I used quite extensively for setting up my home theater so far, but what happened to part 3-6?
We can hope that Lee gets the
We can hope that Lee gets the time to put this together, and perhaps a little more money to pick up more components to offer his expert opinion on.
You r too much…great
You r too much…great article….Now can we have the last bits? I write from Nigeria……