Bundled Applications
Included Applications
- ASUS AI Suite 3
- ASUS Dual Intelligent Processors 5 with 5-Way Optimization
- TPU (Turbo Processing Unit)
- EPU (Energy Processing Unit)
- DIGI+ Power Control
- Fan XPert4
- Turbo App
- USB 3.1 Boost
- AI Charger+
- PC Streamer
- Disk Unlocker
- ASUS Wi-Fi GO!
- ROG RAMCache
- ROG CPU-Z
- ROG AURA RGB Lighting Control
- GameFirst IV
- DAEMON Tools Pro Standard
- ASUS WebStorage
- Overwolf
- Kaspersky® Anti-Virus
AI Suite 3
The AI Suite 3 application is a bundling mechanism for all the included ASUS designed utilities, providing a centralized panel from which to access and run the applets. All applets can be accessed by clicking on the expansion button on the middle left side of the page. The applet list then slides out to the right in a frame along the inside left of the page. The AI Charger+ applet configure the USB port for optimized fast-charging of Apple-specific or generic USB-based devices. The USB 3.1 Boost applet supercharges your USB 3.1 ports, allowing for enhanced read and write performance with the amount of performance gain based on the USB 3 device in use. The Overwolf utility is an in-game overlay that allow for display of an in-game utility bar for accessing a variety of apps and functions without leaving the game interface. ASUS offers a variety of premade skins and overlays through their ROG site.
Dual Intelligent Processors 5
The main app opens to the Dual Intelligent Processors 5 page, organized into separate sections for each of the five 5-Way Optimization features. The overclocking settings are housed in the TPU section. The EPU section houses power saving related settings. The DIGI+ VRM section houses settings specific to the board power circuitry, and the Fan Xpert4 section contains fan controls. The Turbo App section houses application specific performance, network priority, and audio settings. Along the top of the app are the current power saving settings enacted and the start button for the 5-Way Optimization wizard. Along the bottom of the app are real-time monitoring display settings.
5-Way Optimizations Wizard start page, TPU section
5-Way Optimizations Wizard start page, TPU, EPU, and Fan sections
5-Way Optimizations Wizard start page, Digi+ Power Control and Graphics Cards sections
5-Way Optimization Wizard warning message
5-Way Optimization Wizard in progress, TPU test
5-Way Optimization Wizard in progress, TPU test continued
5-Way Optimization Wizard in progress, Fan Xpert4 test
5-Way Optimization Wizard in progress, EPU test
5-Way Optimization Wizard in progress, Digi+ Power Control test
5-Way Optimization Wizard in progress, Graphics Card test
5-Way Optimization Report, TPU and EPU sections
5-Way Optimization Report, Fan section
5-Way Optimization Report, Fan and VGA sections
TPU, CPU Frequency settings page
TPU, CPU Strap settings page
TPU, Graphics Cards settings page
Fan Xpert4 page
Fan Xpert4, Fan details page
DIGI+ Power Control, CPU settings page
DIGI+ Power Control, DRAM settings page
Turbo App page
EPU page
Can both the U.2 and M.2
Can both the U.2 and M.2 ports be used simultaneously?
It looks likes you can, but
It looks likes you can, but M.2 is favored over U.2. In the BIOS, you can specify two use one or the other as well.
Yes, but the manual for this
Yes, but the manual for this motherboard says it shares bandwidth with the M.2 slot.
In fact most things are shared (WiFi, USB3.1) if you only have a 28 lane CPU.
yes you can.
yes you can.
Would you know if ASUS will
Would you know if ASUS will be revising their X99 MICRO ATX motherboard?
Saving for the ASUS X99-M WS and will make the purchase by the end of the year. But would be nice to know if a newer board will be released then which includes various improvements as seen on the other boards.
I am not sure, truthfully,
I am not sure, truthfully, but have not heard of a revision coming out…
I have this motherboard along
I have this motherboard along with Corsair LPX 3200MHz, 4x16GB modules.
The issue I have with it (and if you read a lot of newegg reviews) is that the board will not post above DDR4 2400MHz with this memory. Is it just the size of my RAM and compatibility?
When it doesn’t post, the only way to get it back is to unplug it, remove the battery, and clear the CMOS. Then you have to hold the power button for 20-30 seconds. Then it posts.
It’s ridiculous and I can see why so many newegg reviews claim it doesn’t boot after a week.
Did it pose any problems for you?
Right now I’m running it at 2133MHz just because I’m tired of it not turning back on if I shut it down.
It’s weird though because I can get it to boot at 3200MHz after it successfully boots at 2133MHz. Until I shut it down. Restarts are fine. And sleeping is fine.
I had a hard time dialing it
I had a hard time dialing it in for overclocking and did notice an issue getting high memory speeds to work, but was able to get similar corsair modules to boot and run stable at 3200MHz. My testing was done with a Haswell processor.
Were you using a Haswell or Broadwell processor in your system?
I replied to the wrong
I replied to the wrong comment, but you can find my reply under hechacker1.
Thanks. 6800k in my
Thanks. 6800k in my system.
My system actually runs stable at 3200MHz memory using XMP, along with a 4.5GHz on all cores at 1.370v (I won the silicon lottery?). I played around with the cache multiplier, but that didn’t make a difference in it booting.
Everything else is basically set to auto voltages.
The issue is simply that it won’t boot with the RAM at higher clocks from a cold boot. With a warm reboot and it’s fine.
I didn’t buy a 4x16GB kit, rather 2 kits since it was cheaper.
That’s an odd one. I did
That's an odd one. I did have quite a time getting the board to board with RAM at 3200MHz, but, it did eventually once i got it dialed in (without using the XMP setting too).The board itself is just a bit "finnicky", but that may have more to do with the changes made to support the Broadwell processor perhaps. Didn't have the same challenges with older X99 boards. (Note that this is speculation on my part based on testing experiences, and not based on anything I've heard/been told by ASUS or other manufacturers).
One thing to check is the BIOS version, make sure to update to the latest if you haven't already.
One other thing, Raja from ASUS put out this very comprehensive guide on overclocking the Broadwell-E processor on X99 boards, that also includes memory tweaking. I found it very useful myself:
http://edgeup.asus.com/2016/06/17/broadwell-e-overclocking-guide/
The thing is (and I’m a Strix
The thing is (and I’m a Strix x99 gaming motherboard owner) that this board is marketed as an overclocker’s dream, but in actual life it’s the furthest thing from it.
It seems to have issues even at factory settings, it’s quite choosy about RAM, and it has a delicate voltage regulation circuitry – I’ve had to RMA it AND my CPU after the dreaded QCODE 00 hit my board one morning a few months after assembling my rig. And I know that others with this model encountered it as well.
Now I’m pretty stable (the board alternates between Qcode AA and Qcode 40 most of the time) with the latest bios, and a UPS unit to make sure that there are no spikes. But I would think twice about buying a board from this series again. Even the newer x299 LGA2066 model. Just my two cents.
Hello new here
I have this
Hello new here
I have this motherboard i have purchased a msi gaming x TRIO 2080ti and wanted to get another. However it wont fit two cards the the x16 slots ie top and middle pcie slots. if i was to add the second card to the bottom pcie slot would it still link as x16 or x8? as u can probably tell im not spend another 1300 on a card if the wont link at x16 on both cards. any help would be much appreciated.
Thank you in advance.
THIS IS A FANTASTIC BOARD BUT I DO GET THE ODD OVERCLOCKING ERRORS EVERY NOW AND THEN